Castle Auto Enterprises

E.F.I. wiring kits for Gemini - TC-TD-TE-TF-TX

V6 EFI Engine Conversion

Details for Customer

For a V6 application, the engine mounts are used in conjunction with original red motor 6cyl rubbers.

The engine bay harness is connected to original loom under D/side dash and control loom is mounted on D/side inner fender.

The E.C.M. is mounted on the LHS kick panel or above the glove box.

Our loom is sold on a changeover basis for the engine to computer loom.
If no changeover loom is supplied, an additional cost of $200.00 will apply.

Prices may vary slightly if an Ecotech engine is used.

LOOMEFI-01 Engine Management loom to suit Holden Series 1 & 2 V6 Commodore Engines $600 c/o

LOOMEFI-08 Engine Management loom to suit Holden V6 Ecotec Engines $700 c/o

MEMCAL-VT/V8 Re-programmed Memcal to Delete Vehicle Anti-Theft System (VATS) & Calibrated to suit conversion. $450c/o

MEMCAL-VT/V6 Re-programmed Memcal to Delete Vehicle Anti-Theft System (VATS) & Calibrated to suit conversion. $450c/o

MEMCAL-VR/V6 Man Re-Programmed Memcal to Delete Vehicle Anti-Theft System (VATS) & Calibrated to suit Conversion. $450c/o

MEMCAL-VR/V6 AUTO Re-programmed Memcal to Delete Vehicle Anti-Theft System (VATS) & Calibrated to suit conversion. $450c/o

LOOMS/S-01 Speed Sensor assembly & Loom with speedo cable provision. Suit T-700 Auto Trans. $250

LOOMS/S-02 Speed Sensor assembly & Loom with speedo cable provision. Suit T-350-400. Powerglide Auto Trans. $200

B0580464070 Hi-pressure EFI fuel pump $195 Single click for Image.

BF-5030 Hi-pressure fuel filter $20 Single click for Image.

11004/KIT Lift pump. Low pressure $140 Single click for Image.

ST-4 EFI Surge Tank $150 Single click for Image.

FAN-EF4026 16'' 2100cfm UNIVERSAL FAN $180

SUMP-04B V6 Commodore suit early Holdens and Toranas. Reversed Sump including Pickup $660 Single click for Image.

SUMP-04A V6 Commodore Ecotec alloy sump suit Early Holdens and Toranas. Reversed Sump including Pickup $660 Single click for Image.

CH-EM64 HOLDEN GEMINI WITH COMMODORE V6 (INCLUDES RUBBERS) $353

XM-01 Transmission Cross-member to suit Conversion Applications $187

A1158 Transmission rubber mount to suit T700 and T5 $44 Single click for Image.

CH-74 HOLDEN GEMINI WITH V6 3.8 EFI COMMODORE ENGINE 3 INTO 1 DESIGN. 1 5/8'' (must use engine mounts EM-64) $720 Single click for Image.

CH-76 HOLDEN TORANA LH-LX-UC and HQ-WB WITH V6 3.8 EFI COMMODORE ENGINE. 3 INTO 1 DESIGN. 1 5/8'' INCLUDES Y-PIECE (must use engine mounts CH-EM60) $550 Single click for Image.

SPEEDO-1 Holden HJ to HZ Electronic Speedo and Tacho conversion. $880 Single click for Image.

G/R-03/V6A1.9 V6 3.8ltr Commodore Engine. Suit Automatic trans. (9 Tooth pinion) $350 Single click for Image.

G/R-03/V6M1.9 V6 3.8ltr Commodore Engine. Suit Manual trans. (10 Tooth pinion) $350 Single click for Image.

PULLEY-01 Idler Pulley for Holden V6. Use as a replacement when not using Power Steering pump. $270 Single click for Image.

All Prices in $Au including GST. Overseas orders will be lower. 
Back to the EFI wiring page

-